Shandong Juhuo Special Steel Co., LTD +86 139 1137 1422 sale3@sdjhtg.com
Product introduction
This specification covers wall seamless and welded carbon and alloy steel pipe intended for use at low temperatures. The pipe shall be made by the seamless or welding process with the addition of no filler metal in the welding operation. All seamless and welded pipes shall be treated to control their micro-structure. Tensile tests, impact tests, hydro-static tests, and nondestructive electric tests shall be made in accordance to specified requirements.
1. Scope
1.1 This specification covers nominal (average) wall seamless and welded carbon and alloy steel pipe intended for use at low temperatures. Several grades of ferric steel are included as listed in Table 1. Some product sizes may not be available under this specification because heavier wall thicknesses have an adverse affect on low-temperature impact properties.
1.2 Supplementary Requirement S1 of an optional nature is provided. This shall apply only when specified by the purchaser.
1.3 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in non-conformance with the specification. The inch-pound units shall apply unless the "M" designation of this specification is specified in the order.
Technical data
Seamless Steel Pipe Chemical Composition and Mechanical Properties
This data is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.
Standard | Grade | Chemical Composition (%) | Mechanical Properties | ||||||
ASTM A53 | C | Si | Mn | P | S | Tensile STrength(Mpa) | Yield STrength(Mpa) | ||
A | ≤0.25 | - | ≤0.95 | ≤0.05 | ≤0.06 | ≥330 | ≥205 | ||
B | ≤0.30 | - | ≤1.2 | ≤0.05 | ≤0.06 | ≥415 | ≥240 | ||
ASTM A106 | A | ≤0.30 | ≥0.10 | 0.29-1.06 | ≤0.035 | ≤0.035 | ≥415 | ≥240 | |
B | ≤0.35 | ≥0.10 | 0.29-1.06 | ≤0.035 | ≤0.035 | ≥485 | ≥275 | ||
ASTM A179 | A179 | 0.06-0.18 | - | 0.27-0.63 | ≤0.035 | ≤0.035 | ≥325 | ≥180 | |
ASTM A192 | A192 | 0.06-0.18 | ≤0.25 | 0.27-0.63 | ≤0.035 | ≤0.035 | ≥325 | ≥180 | |
API 5L PSL1 | A | 0.22 | - | 0.90 | 0.030 | 0.030 | ≥331 | ≥207 | |
B | 0.28 | - | 1.20 | 0.030 | 0.030 | ≥414 | ≥241 | ||
X42 | 0.28 | - | 1.30 | 0.030 | 0.030 | ≥414 | ≥290 | ||
X46 | 0.28 | - | 1.40 | 0.030 | 0.030 | ≥434 | ≥317 | ||
X52 | 0.28 | - | 1.40 | 0.030 | 0.030 | ≥455 | ≥359 | ||
X56 | 0.28 | - | 1.40 | 0.030 | 0.030 | ≥490 | ≥386 | ||
X60 | 0.28 | - | 1.40 | 0.030 | 0.030 | ≥517 | ≥448 | ||
X65 | 0.28 | - | 1.40 | 0.030 | 0.030 | ≥531 | ≥448 | ||
X70 | 0.28 | - | 1.40 | 0.030 | 0.030 | ≥565 | ≥483 | ||
API 5L PSL2 | B | 0.24 | - | 1.20 | 0.025 | 0.015 | ≥414 | ≥241 | |
X42 | 0.24 | - | 1.30 | 0.025 | 0.015 | ≥414 | ≥290 | ||
X46 | 0.24 | - | 1.40 | 0.025 | 0.015 | ≥434 | ≥317 | ||
X52 | 0.24 | - | 1.40 | 0.025 | 0.015 | ≥455 | ≥359 | ||
X56 | 0.24 | - | 1.40 | 0.025 | 0.015 | ≥490 | ≥386 | ||
X60 | 0.24 | - | 1.40 | 0.025 | 0.015 | ≥517 | ≥414 | ||
X65 | 0.24 | - | 1.40 | 0.025 | 0.015 | ≥531 | ≥448 | ||
X70 | 0.24 | - | 1.40 | 0.025 | 0.015 | ≥565 | ≥483 | ||
X80 | 0.24 | - | 1.40 | 0.025 | 0.015 | ≥621 | ≥552 |
Carbon Steel Seamless Pipe Chemical Composition and Mechanical Properties
Standard | Grade | Chemical Composition | Mechanical Properties | |||||||||
C | Si | Mn | P | S | Cr | Ni | Cu | Tensile Strength(Mpa) | Yield Strength(Mpa) | Elongation(%) | ||
GB/T8163 | 10 | 0.07-0.14 | 0.17-0.37 | 0.35-0.65 | ≤0.035 | ≤0.035 | ≤0.15 | ≤0.25 | ≤0.25 | 335-457 | ≥205 | ≥24 |
20 | 0.17-0.24 | 0.17-0.37 | 0.35-0.65 | ≤0.035 | ≤0.035 | ≤0.25 | ≤0.25 | ≤0.25 | 410-550 | ≥245 | ≥20 | |
Q345 | 0.12-0.20 | 0.20-0.55 | 1.20-1.60 | ≤0.045 | ≤0.045 | - | - | - | 490-665 | ≥325 | ≥21 |
Carbon Steel Seamless Pipe Tolerance
Pipe types | Pipe Szie(mm) | Tolerances | |
Hot rolled | OD | All | ±1% (min ±0.50mm) |
WT | All | +15%, -12.5% | |
Cold drawn | OD | 6~10 | ±0.20mm |
10~30 | ±0.40mm | ||
30~50 | ±0.45mm | ||
>50 | ±1% | ||
WT | ≤1 | ±0.15mm | |
>1~3 | +15% -10% | ||
>3 | +12.5% -10% |
Seamless Steel Pipe End
Plain End | Wall Thickness less than 0.5 inch, including SCH STD & SCH XS |
Plain End (Square Cut) | Wall Thickness over 0.5 inch, including SCH XXS |
Beveled End | Wall Thickness less than 0.5 inch, including SCH STD & SCH XS |
Couplings | Outside Diameter equal or less than 2'' |
Thread Protection | Outside Diameter over 4 inch |
Warehouse Storage
Shandong Juhuo Special Steel Co., Ltd. is a comprehensive enterpriseintegrating steel supply and processing. The company has a large inventory of metal materials such as stainless steel, galvanized, profiles, aluminum.copper, lead, etc, which can meet the needs of customers in different fields.The company has strong strength and has a professional team with excellent technology and rich experience.The company has also introduced advanced production equipment and processing technology, which can provide customers with steel products of various specifications and processing requirements.
Customer conversation
We provide the products consultation , purchase plan suggestion , logistic service ( including the shipment service , custom works ,etc ).
Application field
Taking technology as the guide, quality as the guarantee, and service as the purpose, the company actively explores the market, expands the scale of operation, and constantly improves enterprise management to ensure product quality and service quality.
The inner layer is packed with waterproof paper, the outer layer is packed with iron sheets, and fixed with fumigated wooden pallets. It can effectively protect the product from corrosion during the shipping process.
Sure, we can send samples all over the world, and our samples are free.
You need to provide the grade, width, thickness, coating, and tonnage you need to buy.
Under normal circumstances, we ship from Shanghai, Tianjin, Qingdao, Ningbo and other ports, you can choose other ports according to your needs.
Due to the cyclical changes in raw material prices, prices vary from period to period.
We have ISO9001, SGS, EWC and other certifications.
Generally speaking, our delivery time is within 30-45 days, it may be delayed if there is a large demand or special circumstances.
Of course, we welcome customers from all over the world to visit our factory.
Of course, all of our products are strictly quality tested before packing, and unqualified products will be destroyed.
Under normal circumstances, our online service time is 8:00-22:00 Beijing time, after 22:00, we will reply to your inquiry on the next working day.